Dosing complex DCM-60
16 764 348 ₸
Enquire conditions
and delivery time
We'll call you back within 15 minutes
Specify your requirements
Send prices and terms of delivery
Aggregate bins (3 x 20). Total volume 60 m³ |
Preparation under registers installation for heating inert materials |
Sector valves, with control of pneumatic cylinders - 6 pcs. |
Pneumatic equipment - 6 electro-pneumatic distributors, a set of fittings and tubes, 6 quick exhaust valves, 1 pneumatic regulator, a filter with a pressure gauge |
Vibrator MVE3003 - 6 pcs. |
The support frame, installation without foundation |
Dispenser inert CI-9 (conveyor) with the lined drive drum. Drive power 18,5 kW |
Zink plated rollers |
Тензодатчик BSA-2 "Cas" (Ю. Корея) - 4 шт. |
Коробка соединительная "CAS" (Ю. Корея) |
Signal amplifier - weight sensor |
Passport to complex metering and purchased products |
Compressor SB4/F-270.LB50 |
Remote Control Manual |
Automatic control panel |
The soft starter, frequency converter |
Lattices on bunkers |
Registers for heating |
Covers for bunkers |
DCM-60 for installation of the metering complex It does not require the production of special foundation, The complex is set on a flat, dense area.
The total volume of bunkers is 60 m³ (each bunker has a volume of 20 m³), three bunkers are installed on a special frame. Each bunker has two sector gates, which are controlled using a pneumatic cylinder installed on it. Due to the use of two shutters: the main one and the additional one, it is possible to achieve high accuracy. Each section is equipped with a vibrator-shaker MVE 300/3, 6 pieces in total.
To ensure the operation of the dosing complex, it must be connected to a compressed air line with a working pressure of at least 0.6 MPa. To install the compressor, a platform for its placement is already provided in the frame of the dosing complex. This allows close the compressor from the influence of dust from the plant and atmospheric precipitation.
The inert dispenser (conveyor) DI-9 is installed under the bunkers on four high-precision strain gauges "Case" (Ю. Корея) SBA-2T a total capacity of 8 tons.
Inert materials (sand, screenings, crushed stone, etc.) are fed into the bunkers using lifting mechanisms. To protect against large fractions getting into the bunkers, gratings with a cell of 100 mm x 100 mm or other sizes (optional) can be installed on the bunkers.
Further, all work is carried out using the control panel (depending on the selected configuration, delivery with an automatic control panel is possible). The gates of the two sections of the first bunker are opened and the main dose of the first component is supplied. Accurate dosing is carried out by automatic and pulsed opening of the bunker gates.
The operator automatically monitors the set of the required dose. If there is difficulty in feeding inert materials from the bunkers, the MVE 300/3 vibrator-shakers on the required section of the bunker are briefly activated. As the collection and weighing proceeds, the automation turns on the drive of the DI-9 dosing conveyor and the weighed dose of inert substances enters the receiving hopper. Then, in the same sequence, the next component is fed and weighed from the second hopper.
After unloading conveyor-dispenser inert CI-9, dosing cycle repeats.
Can be supplied in a protective coating of zinc. The coating is applied by cold galvanizing.
- It does not require the production of foundation
- Perevozitsya in 1 evrofure
- 3 bunkers per 20 m³ every (total volume 60 m³)
- Loading width 3.2 meters, loading height 4.4 meters
- Accurate dosing - accuracy better than ± 1%
- Lined the drive drum, galvanized rollers
Technical Features
- The total volume of bunkers, the cube. m. 60
- The volume of the hopper, the cube. m. 20
- The number of bins, pieces. 3
- The maximum dose weighing kg up to 4500
- Batching error,% ±1
- Belt speed, m c 1,9
- The pressure in the pneumatic system, MPa 0,6...0,8
- Aggregate size, mm max 100
- Supply voltage, V/Hz 360/50
- Power installed, kW 20,3
- Shutter sector, pneumatic cylinders control, pcs. 6
- Weight, kg 9300
- Height, mm 4404
- Width, mm 3589
- Length, mm 10388
Quality
certificates
Products
in stock
Individual configuration
with prices for each item
Mobile
commissioning team
available
Worldwide
delivery
in trucks or containers
Call hotline in Kazakhstan
Our managers will answer all your questions from Monday till Friday:
from 06:00 a.m. to 05:00 p.m. (GMT+3, Moscow time)
Address: 010000, Kazakhstan, Akmola region,
Astana, Al-Farabi Avenue, building 44, office. 32
e-mail: sales@zzbo.ru
Artem Kononovich
Director of the branch in Kazakhstan
Phone: +7 (7172) 760-141
e-mail: sales@zzbo.kz
Place your order
We will send you the price,
conditions and terms of delivery
Response within 1 hour
You will get the offer with
individual delivery and payment conditions