Dosing complex DKS-32
14 388 192 ₸




Enquire conditions
and delivery time

We'll call you back within 15 minutes

Specify your requirements

Send prices and terms of delivery
Bunker-Inertia BI-32 (4 x 8)-4 bunkers. Total volume 32 m³ |
Preparation under registers installation for heating inert materials |
Sector valves, with control of pneumatic cylinders - 4 pcs. |
Pneumatic equipment - 4 electrical distributor, a set of fittings and tubes, 4 valves of a fast exhaust, 1 pneumatic regulatory, a filter with a pressure gauge |
Vibrator MVE 300/3 - 4 pcs. |
The support frame, installation without foundation |
Дозатор инертных ДИ-12 (конвейер) с футерованным приводным барабаном. Мощность привода 11 кВт |
Zink plated rollers |
S-shaped tensodists for 2 tons- 6 pcs. |
CAS connecting box |
Signal amplifier - weight sensor |
Passport to complex metering and purchased products |
Compressor SB4/C-200.LB30-3.0 |
Dosage complex control panel for DKS |
The soft starter, frequency converter |
Grating on the hopper |
Reverse conveyor operation |
Registers for heating |
Caps for bunker |
For installation of a dosing complex DKS-32 It does not require the production of special foundation, The complex is set on a flat, dense area.
Four bunkers are installed on a special frame. Each bunker with a volume of 8 m³ has one sector shutter, which is controlled using the pneumatic cylinder installed on it. On each bunker, the MVE 300/3 vibrator is installed, only 4 pieces.
To ensure the performance of the metering complex, it must be connected to a compressed air line with a working pressure of at least 0.6 MPa. To install the compressor, a platform for its placement is already provided in the frame of the metering complex. This allows you to close the compressor from the influence of dust from the plant and atmospheric precipitation.
Dispenser inert (conveyor) CI-12 suspended under the hoppers in the six high-precision load cells a total capacity of 12 tons.
Inert materials (sand, screenings, crushed stone, etc.) are fed into the bunkers with the help of hoisting mechanisms. Grids can be installed on the bunkers to protect against ingress of large fractions into the bunkers with cell 100 mm x 100 mm with cell 100 mm x 100 mm
Далее вся работа осуществляется с помощью пульта управления (зависит от выбранной комплектации, возможна поставка с автоматическим пультом управления). Открывается затвор первого бункера и подается основная доза первого компонента. Точная дозация осуществляется автоматикой и импульсным открытием затвора.
The set of the required dose operator is monitored by automation. If it is difficult to submit inert from the bunkers, the vibrator-conjuvener MVE 300/3 on the required bunker is acted briefly. As the set and weighing, the automation includes the drive of the DI-12 conveyor and the suspended dose of inertia enters the receiving hopper. Further, in the same sequence, the following component from the second bunker is submitted and weighed.
After unloading conveyor-dispenser inert CI-12 dosing cycle repeats.
Can be supplied in a protective coating of zinc. The coating is applied by cold galvanizing.
- 4 bunkers of 8 cubic meters each (total volume 32 m³)
- It does not require the production of foundation
- 4 bins of 8 cubic meters each (total volume 32 cubic meters)
- 4 bins of 8 cubic meters each (total volume 32 cubic meters)
- Accurate dosing - accuracy better than ± 1%
- Lined the drive drum, galvanized rollers
- 2-year warranty
Technical Features
- Total volume of bunkers, m³ 32
- Volume of one bunker, m³ 8
- The number of bins, pieces. 4
- The maximum dose weighing kg 14 910 $
- Batching error,% ±1
- Belt speed, m c 1
- The pressure in the pneumatic system, MPa 0,6
- Aggregate size, mm max 100
- Supply voltage, V/Hz 380/50
- Power installed, kW 4 bins of 8 cubic meters each (total volume 32 cubic meters)
- Shutter sector, pneumatic cylinders control, pcs. 4
- Weight, kg 4 bins of 8 cubic meters each (total volume 32 cubic meters)
- Height, mm 4 bins of 8 cubic meters each (total volume 32 cubic meters)
- Width, mm 2,500
- Length, mm 4 bins of 8 cubic meters each (total volume 32 cubic meters)

Quality
certificates

Products
in stock

Individual configuration
with prices for each item

Mobile
commissioning
available

Worldwide
delivery
in trucks or containers
Geography of supplies 2011-2024
Own production, in-stock products and
professional team allow us guarantee
most competitive prices, shortest
possible delivery time and high-quality goods
Call hotline in Kazakhstan
Our managers will answer all your questions from Monday till Friday:
from 06:00 a.m. to 05:00 p.m. (GMT+3, Moscow time)
Address: 010000, Kazakhstan, Akmola region,
г. Astana, prospekt Akžol, Zdanie 44, of. 32
e-mail: sales@zzbo.ru

Artem Kononovich
Director of the branch in Kazakhstan
Phone: +7 (7172) 760-141
e-mail: sales@zzbo.kz
Place your order
We will send you the price,
conditions and terms of delivery

Response within 1 hour

You will get the offer with
individual delivery and payment conditions