Onsite mobile Onsite mobile, with a capacity of up to 35 cubic meters of concrete per hour of operation. Line of factories QUICK BETON — These are quick-mounted RBUs ​​that do not require the preparation of a high-strength surface for installation, and also have the ability to install a frame chassis for more mobile operation.

Carriage in a 40 ton container or eurowaggon.

The plant is delivered completely ready for operation and does not require foundation preparation or lengthy setup.
Installed in an open area on any dense surface without preparation, or in any room with a ceiling height of at least 7.5 meters.

Commissioning is the connection of 380 volts and the supply of water. Takes no more than an hour!

The principle of automatic operation:

• Inert materials (sand, screenings, crushed stone, etc.) that will be used in the production of concrete/mortar are distributed among the inert bin compartments by name. The number of bunkers is 2 pcs., the total volume of bunkers is 12 cubic meters. In the same way, cement in the silo, water and additives are distributed according to the class in the supply tanks.
• After selecting a specific concrete recipe, the required volume (m³) is entered. After that, the plant starts production.
• Inerts are weighed individually according to the mass specified in the recipe. Weighing occurs as a result of opening the valves of the inert hopper and pouring them onto the weighing conveyor.
• The dosed inerts are fed into a twin-shaft concrete mixer via a weighing conveyor.
• Cement, water and various chemicals. additives are fed into the appropriate dispensers, where they are weighed depending on the recipe specified in the automated system.
• After dosing, all components of the concrete mortar are fed one by one through the dispenser valves into the concrete mixer.
• The mixture of all components is mixed in the mixer double shaft for a certain time and as a concrete solution is supplied through the drain valve mixer.

Twin-shaft concrete mixer BP-2G-750

Twin-shaft concrete mixer consists of a stationary welded body with two horizontal shafts with spokes and arms located inside. The shafts are joined by a synchronizing device to protect the drive. Mixture components are loaded directly into the mixer box which is protected from foreign particles by a protecting grid.

Is driven by an electric motor with power of 18.5 kW through the belt drive, equipped with a jacket and a powerful crane reducer. Mixing shaft rotation speed 36 rotations per minuteMixer box is coated from the inside by wear-resistant armor, flake type. . Броня сменная, крепится на винты. Броня чешуйчатого типа, состоящая из элементов, позволяет менять только износившуюся часть брони, что облегчает ремонт и обслуживание. Выгрузка готовой бетонной смеси из двухвального бетоносмесителя производится через окно в днище корпуса, закрываемое двойным секторным затвором with pneumatic lock.

One cycle produces 0.5 cubic meters of concrete. The cycle lasts about 40 seconds. Thus, for one and a half minutes of operation of the QUICK BETON TWIN-35 installation, 1 cubic meter of concrete is produced.

It is possible to supply a concrete plant QUICK BETON TWIN-35 with a planetary concrete mixer BPP-3V-750 with two gates

Onsite mobile

It has a large capacity of 12 cubes of inert materials. These are two bunkers: with a volume of 4 and 8 cubic meters. meters, respectively.

The large loading width of the bunkers is 4.2 meters. The weighing conveyor, on suspended strain gauges, is equipped with a chevron belt and a lined drum, an anti-slip and self-cleaning system. Dosage error 1%.

Conveyor drive power 11 kW.

The bunkers are equipped with two pneumatic valves. Four MVE 300/3 vibrators are installed on the hopper cone on a special platform, fixed through four vibration pads to the wall of the hopper cone, so the impact of vibration on the inert material occurs with the help of a vibrating plate not in contact with the hopper wall. Thus, the impact of the mechanical destructive force of vibration on welded joints of adjacent structures is reduced.

Onsite mobile

The dispenser block consists of a frame, a hopper (dispenser) of cement, a dosing water tank with a pump, two dosing tanks of liquid chemicals. additives.

Рама сборно-сварная из стали. Дозирующий бак снизу восьмиугольной, сверху четырех угольной формы, образованный пирамидой и ее сечением, сварен из листовой стали. Бункер цемента подвешивается на трех тензодатчиках BSA-500L, также являющимися измерителями массы продукта в бункере. Опора имеет 2 отверстия для крепления тензодатчиков. Бак воды с насосом и бак хим. добавок выполнены в форме прямоугольных призм. Бак воды сварной из листовой стали, бак хим. добавок сварной из нержавеющей стали.

The water tank is suspended in the same way as the cement bunker. Bucky chem. additives are suspended on one load cell BCA-100L, which is a mass meter of liquid chemical. additives.

Данные с тензодатчиков обрабатываются сумматором, расположенном в распределительном шкафу. После совершения операции дозирования (наполнении баков необходимой для замеса массой цемента, воды и хим. добавки) автоматически отключается подача в баки и открываются заслонки сброса в смеситель.

Next there is complete devastation tanks.

The package of the concrete plant already includes water pumps and two chemical pumps. additives.

Cement silos, silo piping and augers are always in stock in Zlatoust!

Compressed air system Compressor SB4/F-270.LB50-5.5

Consists of an Italian piston compressor SB4/F-270.LB50-5.5 and pneumatic systems. Capacity 880 liters per minute, power 5.5 kW. Pressure 11 atm. Receiver 270 liters. The compressor is already built into the frame and is protected from the external environment and dust.

PAM 4.0 SCADA control panel

Система управления проста в управлении благодаря графическому дисплею со встроенными клавишами. Для производства необходимо выбрать рецепт и количество бетона.

The PA control panel is designed to control the concrete plant in the following modes:

1. Manual mode. Operation using a graphical control panel with an intuitive panel and display of operation on the touch screen
2. Auto. Operation with Waintek graphical touch terminal. The operator needs to select the recipe and the amount of concrete required, press the “Start” button
3. Work with PC (optional). Work using a personal computer (monoblock) installed at the workplace. Selection (task) of the required recipe and the required number of batches. In addition to the required technological information, the computer screen displays: - messages about malfunctions and errors of the control system - information necessary to account for the consumption of materials (water, cement, electricity, chemical additives) and finished products. Information can be issued for any period of time - year, month, week, day. – information necessary to control the work of personnel (fixing actions, error control, entering incorrect recipes)

Technical Features

• Capacity, cu m per hour 20...35
• Режим работы автоматический на ПО "SCADA" по принципу "одна кнопка"
• 31 095 $ 1
• Hopper capacity, cu. m 12
• Two-shaft concrete mixer BP-2G-750 Two-shaft concrete mixer BP-2G-750
• Total power, kW 42
• Two-shaft concrete mixer BP-2G-750 Two-shaft concrete mixer BP-2G-750
• Weight, kg 10,000
• Height, mm 5962
• Width, mm 4295
• Length, mm 11537