TEPLO TGV-250 used for the operation of the RBU concrete plant in winter. Based on the principle of supplying hot air. Designed for heating inert materials during the production of concrete at ambient temperatures down to minus 45^TheS.

The heat generator supplies heated air with a nominal air temperature of +170 °C under high pressure into air ducts connected to the bunkers. Thermal power of the installation of 250 kW ensures the operation of a concrete plant with a capacity of up to 30 m³/h (depending on the region of operation).

Установка использует непрямой нагрев, при котором тепло от дымовых газов передается воздуху через стенку топки и трубы теплообменника. Т.е. продукты горения не попадают в инертные и соответственно внутрь завода. Теплогенератор состоит из burners Italian made (Baltur or F.B.R.), high pressure fan, firebox, heat exchanger, control panel and automation. The heat exchanger and combustion chamber are made of stainless steel.

The diesel heat generator can additionally be equipped with a fuel tank (with the volume required by the Customer), which will ensure autonomous operation of the unit for a long time.

Optionally, air ducts are supplied to connect the heat generator to the dosing complex.

The heat source is used in electrified areas (optional can work in standalone mode).

СИСТЕМЫ АВТОМАТИЗАЦИИ И УПРАВЛЕНИЯ ТЕПЛОГЕНЕРАТОРА TEPLO ТГВ-250

[parent] => 45 [count] => 6 [filter] => raw )

Automation and intelligent control: The Termodat-11M6 temperature controller is used, which ensures high control accuracy and flexibility of settings. Support for PID controllers for the temperature in the duct and in the furnace, which allows you to accurately maintain the set parameters.

[parent] => 45 [count] => 6 [filter] => raw )

Real time display: температуры в канале, теплообменнике, тока вентилятора;

[parent] => 45 [count] => 6 [filter] => raw )

Protection and diagnostics: Developed alarm system (fan overheating, housing overheating, burner failure). Heat exchanger temperature control and automatic burner shutdown when overheated.

[parent] => 45 [count] => 6 [filter] => raw )

Energy efficiency: Using air recirculation to maintain temperature without constantly running the burner.

[parent] => 45 [count] => 6 [filter] => raw )

Reliability and protection: Shell protection degree IP54 - suitable for work in a workshop or under a canopy. Protection against overloads, overheating, phase asymmetry.

Optional:

Data archive - recording up to 1 million points with time reference.

RS485 interface - support for Modbus ASCII/RTU protocols, connection to PC, SCADA systems.

Possibility of settings: PID parameters; temperature settings; minimum and maximum burner power (1-2 stages); fan rotation speed; access to settings is protected from unauthorized access;

Adjusts burner power and fan speed depending on temperature, reducing energy consumption.

[parent] => 45 [count] => 6 [filter] => raw )

More information about TEPLO heat generators

The price for the thermal center is presented without a burner

Technical Features

• Thermal power, kW 250
• Outlet air flow up to, m³/hour (taking into account air expansion at maximum heating delta) 5,300
• Fan air flow, m³/hour 2800
• Air heating delta, °C 210
• Air pressure at the outlet of the DVT, no more than, Pa 11500
• Maximum outlet air temperature, °C 170
• Time to reach operating mode, no more, min 7
• Gas pressure for heat generator, mbar individually
• DF consumption (no more), kg/h (l/h) 23(28)
• Gas consumption (no more), nm.cub/h 30
• KPD% 90
• Current source 3 f. 220/380V, 50 Hz
• Installed power, kW 24
• Operating temperature, °C from -45 to +40
• Weight, kg 2,500
• Length*, mm 5600
• Width*, mm 2,200
• Height*, mm 2460
• *Transport dimensions