TEPLO TGV-100 heat generator for heating применяется для обогрева производственных помещений, промышленных объектов и участия в технологических процессах сушки. Основан на принципе подаче горячего воздуха температурой до 80 ^TheC. It is possible to work both with and without an air duct system.

Теплогенератор подает нагретый воздух с температурой не более 80^TheС под давлением до 1100 Па. Тепловая мощность установки 100 кВт.

The installation uses indirect heating, in which heat from the flue gases is transferred to the air through the firebox wall and heat exchanger pipes. The heat generator consists of burners Italian production (Baltur or F.B.R.), fan, firebox, heat exchanger, control panel and automation. The heat exchanger is made of stainless steel.

The diesel heat generator can additionally be equipped with a fuel tank (with the volume required by the Customer), which will ensure autonomous operation of the unit for a long time.

TEPLO ТГВ-100 для отопления made in climatic version U-1 with operating temperatures from -45 to +40°C. and does not require a block container when installed outdoors (with an air duct connected).

The heat source is used in electrified areas (optional can work in standalone mode).

СИСТЕМЫ АВТОМАТИЗАЦИИ И УПРАВЛЕНИЯ ТЕПЛОГЕНЕРАТОРА TEPLO ТГВО-100

[parent] => 45 [count] => 6 [filter] => raw )

Automation and intelligent control: The Termodat-11M6 temperature controller is used, which ensures high control accuracy and flexibility of settings. Support for PID controllers for the temperature in the duct and in the furnace, which allows you to accurately maintain the set parameters.

[parent] => 45 [count] => 6 [filter] => raw )

Real time display: temperatures in the duct, heat exchanger, room; fan current;

[parent] => 45 [count] => 6 [filter] => raw )

Protection and diagnostics: Developed alarm system (fan overheating, housing overheating, burner failure). Heat exchanger temperature control and automatic burner shutdown when overheated.

[parent] => 45 [count] => 6 [filter] => raw )

Energy efficiency: Using air recirculation to maintain temperature without constantly running the burner.

[parent] => 45 [count] => 6 [filter] => raw )

Reliability and protection: Shell protection degree IP54 - suitable for work in a workshop or under a canopy. Protection against overloads, overheating, phase asymmetry.

Optional:

Data archive - recording up to 1 million points with time reference.

RS485 interface - support for Modbus ASCII/RTU protocols, connection to PC, SCADA systems.

Possibility of settings: PID parameters; temperature settings; minimum and maximum burner power (1-2 stages); fan rotation speed; access to settings is protected from unauthorized access;

Adjusts burner power and fan speed depending on temperature, reducing energy consumption.

[parent] => 45 [count] => 6 [filter] => raw )

[parent] => 45 [count] => 6 [filter] => raw )

More information about TEPLO heat generators

The price for the thermal center is presented without a burner

Technical Features

• Thermal power, kW 100
• Outlet air flow up to, m³/hour 5000-7000
• Air pressure at the outlet of the DVT, no more than, Pa 900-1100
• Air heating delta, °C 40
• Maximum outlet air temperature, °C 80
• Time to reach operating mode, no more, min 7
• Gas pressure for heat generator, mbar individually
• DF consumption (no more), kg/h (l/h) 9(11)
• Gas consumption (no more), nm.cub/h 12
• KPD% 90
• Current source 3 f. 220/380V, 50 Hz
• Installed power, kW 8
• Operating temperature, °C from -45 to +40
• Weight, kg 750
• Length*, mm 2,500
• Width*, mm 950
• Height*, mm 2110
• *Transport dimensions